DE10 Advance Board Setup: MSEL Settings - Revision history

Bingxia: /* FPPx32 Mode (Default) */

2018-08-30T08:08:17Z

FPPx32 Mode (Default)

← Older revision		Revision as of 08:08, 30 August 2018
Line 2:		Line 2:
	The FPGA Configuration Mode Switch (MSEL) shown in Figure 2-1 is by default set to 001 (MSEL [2:0] = 001). The setting corresponds to FPGA configured from HPS software (in the SD Card) in FPP mode. '''If users want to boot with Linux VNC desktop, please setting MSEL switch in this mode'''.		The FPGA Configuration Mode Switch (MSEL) shown in Figure 2-1 is by default set to 001 (MSEL [2:0] = 001). The setting corresponds to FPGA configured from HPS software (in the SD Card) in FPP mode. '''If users want to boot with Linux VNC desktop, please setting MSEL switch in this mode'''.

-		+	:::[[File:De10-advanced revc msel fppmode.jpg\|500px]]
-	::::Figure 2-1 FPGA Configuration Mode Switch set in FPPx32 Mode ~~<font color="red">(TBD)</font>~~	+	:::::Figure 2-1 FPGA Configuration Mode Switch set in FPPx32 Mode
-		+

	=AS Mode=		=AS Mode=

Bingxia: /* AS Mode */

2018-08-30T07:35:25Z

AS Mode

← Older revision		Revision as of 07:35, 30 August 2018
Line 9:		Line 9:
	When the board is powered on and MSEL [2:0] is set to “010” (See Figure 2-2), the FPGA is configured from EPCQ.		When the board is powered on and MSEL [2:0] is set to “010” (See Figure 2-2), the FPGA is configured from EPCQ.

-		+	:::[[File:De10-advanced revc msel asmode.jpg\|500px]]
-	::::Figure 2-2 FPGA Configuration Mode Switch set in AS Mode ~~<font color="red">(TBD)</font>~~	+	::::::Figure 2-2 FPGA Configuration Mode Switch set in AS Mode


	'''[[DE10-Advance Getting Start Guide revC#Chapter 2 Development Board Setup\|Back]]'''		'''[[DE10-Advance Getting Start Guide revC#Chapter 2 Development Board Setup\|Back]]'''

Bingxia at 03:01, 30 August 2018

2018-08-30T03:01:22Z

← Older revision		Revision as of 03:01, 30 August 2018
Line 11:		Line 11:

	::::Figure 2-2 FPGA Configuration Mode Switch set in AS Mode <font color="red">(TBD)</font>		::::Figure 2-2 FPGA Configuration Mode Switch set in AS Mode <font color="red">(TBD)</font>
		+
		+
		+	'''[[DE10-Advance Getting Start Guide revC#Chapter 2 Development Board Setup\|Back]]'''

Bingxia: Created page with "=FPPx32 Mode (Default)= The FPGA Configuration Mode Switch (MSEL) shown in Figure 2-1 is by default set to 001 (MSEL [2:0] = 001). The setting corresponds to FPGA configured from..."

2018-08-30T03:00:33Z

Created page with "=FPPx32 Mode (Default)= The FPGA Configuration Mode Switch (MSEL) shown in Figure 2-1 is by default set to 001 (MSEL [2:0] = 001). The setting corresponds to FPGA configured from..."

New page

=FPPx32 Mode (Default)=
The FPGA Configuration Mode Switch (MSEL) shown in Figure 2-1 is by default set to 001 (MSEL [2:0] = 001). The setting corresponds to FPGA configured from HPS software (in the SD Card) in FPP mode. '''If users want to boot with Linux VNC desktop, please setting MSEL switch in this mode'''.

::::Figure 2-1 FPGA Configuration Mode Switch set in FPPx32 Mode <font color="red">(TBD)</font>

=AS Mode=
When the board is powered on and MSEL [2:0] is set to “010” (See Figure 2-2), the FPGA is configured from EPCQ.

::::Figure 2-2 FPGA Configuration Mode Switch set in AS Mode <font color="red">(TBD)</font>