DE10 Advance revC demo: Factory Default Code - Revision history

Admin: /* Demonstration Setup */

2018-08-23T08:10:05Z

Demonstration Setup

← Older revision		Revision as of 08:10, 23 August 2018
Line 36:		Line 36:
	[[File:De10-advanced revc demo factory cmd.png\|500px]]		[[File:De10-advanced revc demo factory cmd.png\|500px]]

-	Figure 2-2 menu of Default demonstration	+	:::'''Figure 2-2 menu of Default demonstration'''

-	~~Figure 2~~-~~3 board picture of Default demonstration~~	+	[[File:De10-advanced revc demo factory hdmi Tx.jpg\|500px]]

		+	:::'''Figure 2-3 board picture of Default demonstration
		+	'''

	'''[[DE10-Advance_Demonstration_Manual_revC#Chapter 2 Examples For FPGA\|Back]]'''		'''[[DE10-Advance_Demonstration_Manual_revC#Chapter 2 Examples For FPGA\|Back]]'''

Admin: /* Demonstration Setup */

2018-08-23T07:46:58Z

Demonstration Setup

← Older revision		Revision as of 07:46, 23 August 2018
Line 29:		Line 29:
	#Connect the HDMI TX to displayer via HDMI cable.		#Connect the HDMI TX to displayer via HDMI cable.
	#Power on the DE10-Advanced.		#Power on the DE10-Advanced.
-	#Execute the demo batch file “test.bat” under the batch file folder \ default_code\demo_batch. You will see the menu Figure 6-3	+	#Execute the demo batch file “test.bat” under the batch file folder \ default_code\demo_batch. You will see the menu Figure 2-2
	#Select your choice,and program FPGA or program flash		#Select your choice,and program FPGA or program flash
-	#When the demo is running , you can see the led is blinking and flowing, and the displayer will display the board picture Figure 6-4	+	#When the demo is running , you can see the led is blinking and flowing, and the displayer will display the board picture Figure 2-3


	[[File:De10-advanced revc demo factory cmd.png\|500px]]		[[File:De10-advanced revc demo factory cmd.png\|500px]]

-	Figure 6-3 menu of Default demonstration	+	Figure 2-2 menu of Default demonstration

-	Figure 6-4 board picture of Default demonstration	+	Figure 2-3 board picture of Default demonstration


	'''[[DE10-Advance_Demonstration_Manual_revC#Chapter 2 Examples For FPGA\|Back]]'''		'''[[DE10-Advance_Demonstration_Manual_revC#Chapter 2 Examples For FPGA\|Back]]'''

Admin: /* Demonstration Setup */

2018-08-23T07:44:36Z

Demonstration Setup

← Older revision		Revision as of 07:44, 23 August 2018
Line 39:		Line 39:

	Figure 6-4 board picture of Default demonstration		Figure 6-4 board picture of Default demonstration
		+
		+
		+	'''[[DE10-Advance_Demonstration_Manual_revC#Chapter 2 Examples For FPGA\|Back]]'''

Admin: /* Demonstration Setup */

2018-08-23T07:44:21Z

Demonstration Setup

← Older revision		Revision as of 07:44, 23 August 2018
Line 32:		Line 32:
	#Select your choice,and program FPGA or program flash		#Select your choice,and program FPGA or program flash
	#When the demo is running , you can see the led is blinking and flowing, and the displayer will display the board picture Figure 6-4		#When the demo is running , you can see the led is blinking and flowing, and the displayer will display the board picture Figure 6-4
		+
		+
		+	[[File:De10-advanced revc demo factory cmd.png\|500px]]
		+
		+	Figure 6-3 menu of Default demonstration
		+
		+	Figure 6-4 board picture of Default demonstration

Admin at 07:40, 23 August 2018

2018-08-23T07:40:27Z

← Older revision		Revision as of 07:40, 23 August 2018
Line 1:		Line 1:
	The DE10-Advanced board has a default configuration bit-stream pre-programmed, which demonstrates some of the basic features on board. This demo used LED ,7-Segments, Switch ,		The DE10-Advanced board has a default configuration bit-stream pre-programmed, which demonstrates some of the basic features on board. This demo used LED ,7-Segments, Switch ,
	HDMI transmitter display and fan control.		HDMI transmitter display and fan control.
		+
		+	=Function Block Diagram=
		+	Figure 2-1 shows the function block diagram of this demonstration..This demo used fan controller to control fan and used frame buffer read board picture from ON-CHIP-MEMORY,and used scaler scale the picture to 1920x1080 size,display the picture by HDMI TX.
		+
		+
		+	[[File:De10 advanced revc demo default code.jpg\|800px]]
		+
		+	::::::'''Figure 6-2 Block diagram of Default demonstration'''
		+	=Design Tools=
		+
		+	*Quartus Prime 18.0.0 Standard Edition
		+	*Demonstration Source Code:
		+	**Project Directory: Demonstration\default_code
		+	**Bit Stream: default_code.sof or default_code.jic
		+	**Demonstration Batch File: default_code\demo_batch or default_code\demo_run_batch
		+
		+	NOTE : because the demo include software , and run on on-chip-memory, so use mem_init can package elf to sof ,so user can only program sof or sof +elf to run demo
		+
		+	The demo batch file includes following files:
		+	:*Batch File: test.bat
		+	:*FPGA Configuration File: default_code.sof or default_code.jic
		+
		+	=Demonstration Setup=
		+
		+	#Make sure Quartus Prime is installed on the host PC.
		+	#Connect DE10-Advanced board to the host PC via USB cable. Install the USB-Blaster II driver if necessary.
		+	#Connect the HDMI TX to displayer via HDMI cable.
		+	#Power on the DE10-Advanced.
		+	#Execute the demo batch file “test.bat” under the batch file folder \ default_code\demo_batch. You will see the menu Figure 6-3
		+	#Select your choice,and program FPGA or program flash
		+	#When the demo is running , you can see the led is blinking and flowing, and the displayer will display the board picture Figure 6-4

Admin: Created page with "The DE10-Advanced board has a default configuration bit-stream pre-programmed, which demonstrates some of the basic features on board. This demo used LED ,7-Segments, Switch , HD..."

2018-08-23T07:28:09Z

Created page with "The DE10-Advanced board has a default configuration bit-stream pre-programmed, which demonstrates some of the basic features on board. This demo used LED ,7-Segments, Switch , HD..."

New page

The DE10-Advanced board has a default configuration bit-stream pre-programmed, which demonstrates some of the basic features on board. This demo used LED ,7-Segments, Switch ,
HDMI transmitter display and fan control.