F2G with intel A10GFP - Revision history

Admin: /* Other considerations */

2020-09-01T06:50:18Z

Other considerations

← Older revision		Revision as of 06:50, 1 September 2020
Line 29:		Line 29:

	= Other considerations =		= Other considerations =
-	Because the HPC area pin of FMC on Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:	+	Because the HPC area pin of FMC on Arria® 10 GX FPGA Development Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:

	*Remove the resistors for switch and button functions		*Remove the resistors for switch and button functions

Admin: /* GPIO Using Status */

2020-09-01T06:49:41Z

GPIO Using Status

← Older revision		Revision as of 06:49, 1 September 2020
Line 10:		Line 10:


-	On the Kit board, some FPGA I/Os connected to the F2G GPIO connector will have termination resistors(for differential protocol). It is recommended to remove these resistors, otherwise the pins of the GPIO connector will interfere with each other when using in single-end state. <span style="color:#0000ff;"> When the F2G is conneted to the '''FMCA''' connector of the kit.'''Please remove R383,R369 and R336 on the Arria® 10 GX FPGA Development Kit.''' When the F2G is conneted to the '''FMCB''' connector of the kit, please remove '''R349,R333 and R379'''.</span>	+	On the Arria® 10 GX FPGA Development Kit board, some FPGA I/Os connected to the F2G GPIO connector will have termination resistors(for differential protocol). It is recommended to remove these resistors, otherwise the pins of the GPIO connector will interfere with each other when using in single-end state. <span style="color:#0000ff;"> When the F2G is conneted to the '''FMCA''' connector of the kit.'''Please remove R383,R369 and R336 on the Arria® 10 GX FPGA Development Kit.''' When the F2G is conneted to the '''FMCB''' connector of the kit, please remove '''R349,R333 and R379'''.</span>

Admin: /* Other considerations */

2020-09-01T06:46:15Z

Other considerations

← Older revision		Revision as of 06:46, 1 September 2020
Line 29:		Line 29:

	= Other considerations =		= Other considerations =
-	Because the HPC area pin of ~~FMS~~ on Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:	+	Because the HPC area pin of FMC on Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:

	*Remove the resistors for switch and button functions		*Remove the resistors for switch and button functions

Admin: /* Other considerations */

2020-06-19T01:59:32Z

Other considerations

← Older revision		Revision as of 01:59, 19 June 2020
Line 40:		Line 40:
	<noinclude>		<noinclude>
	[[Category:F2G]]		[[Category:F2G]]
		+	[[Category:FAQ]]
	</noinclude>		</noinclude>

Admin: /* Other considerations */

2020-06-19T01:44:31Z

Other considerations

← Older revision		Revision as of 01:44, 19 June 2020
Line 36:		Line 36:

	*Remove the resistors for TMD header functions		*Remove the resistors for TMD header functions
-	*:Please remove ''R4 ~ R11''' for for disconnecting these functions from the FPGA transciver.	+	*:Please remove '''R4 ~ R11''' for for disconnecting these functions from the FPGA transciver.
	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05a.jpg\|800px]]</div>		<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05a.jpg\|800px]]</div>
	<noinclude>		<noinclude>
	[[Category:F2G]]		[[Category:F2G]]
	</noinclude>		</noinclude>

Admin: /* Other considerations */

2020-06-19T01:44:09Z

Other considerations

← Older revision		Revision as of 01:44, 19 June 2020
Line 31:		Line 31:
	Because the HPC area pin of FMS on Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:		Because the HPC area pin of FMS on Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:

-	*Remove the ~~resistor~~ for switch and button functions	+	*Remove the resistors for switch and button functions
	*:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver.		*:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver.
	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 04.jpg\|1200px]]</div>		<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 04.jpg\|1200px]]</div>

-	*Remove the ~~Schittky barrier diode~~ for TMD header functions	+	*Remove the resistors for TMD header functions
	*:Please remove ''R4 ~ R11''' for for disconnecting these functions from the FPGA transciver.		*:Please remove ''R4 ~ R11''' for for disconnecting these functions from the FPGA transciver.
	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05a.jpg\|800px]]</div>		<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05a.jpg\|800px]]</div>

Admin: /* Other considerations */

2020-06-19T01:43:43Z

Other considerations

← Older revision		Revision as of 01:43, 19 June 2020
Line 36:		Line 36:

	*Remove the Schittky barrier diode for TMD header functions		*Remove the Schittky barrier diode for TMD header functions
-	*:Please remove ''~~'D7,D8,D9 and D10~~''' for for disconnecting these functions from the FPGA transciver.	+	*:Please remove ''R4 ~ R11''' for for disconnecting these functions from the FPGA transciver.
-	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05.jpg\|800px]]</div>	+	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05a.jpg\|800px]]</div>
	<noinclude>		<noinclude>
	[[Category:F2G]]		[[Category:F2G]]
	</noinclude>		</noinclude>

Admin: /* Other considerations */

2020-06-19T01:41:56Z

Other considerations

← Older revision		Revision as of 01:41, 19 June 2020
Line 33:		Line 33:
	*Remove the resistor for switch and button functions		*Remove the resistor for switch and button functions
	*:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver.		*:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver.
-	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 04.jpg\|~~800px~~]]</div>	+	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 04.jpg\|1200px]]</div>
-		+

		+	*Remove the Schittky barrier diode for TMD header functions
		+	*:Please remove '''D7,D8,D9 and D10''' for for disconnecting these functions from the FPGA transciver.
		+	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05.jpg\|800px]]</div>
	<noinclude>		<noinclude>
	[[Category:F2G]]		[[Category:F2G]]
	</noinclude>		</noinclude>

Admin: /* Other considerations */

2020-06-19T01:37:07Z

Other considerations

← Older revision		Revision as of 01:37, 19 June 2020
Line 32:		Line 32:

	*Remove the resistor for switch and button functions		*Remove the resistor for switch and button functions
-	*:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver	+	*:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver.
		+	<div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 04.jpg\|800px]]</div>
		+
		+
	<noinclude>		<noinclude>
	[[Category:F2G]]		[[Category:F2G]]
	</noinclude>		</noinclude>

Admin: /* Other considerations */

2020-06-19T01:36:39Z

Other considerations

← Older revision		Revision as of 01:36, 19 June 2020
Line 31:		Line 31:
	Because the HPC area pin of FMS on Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:		Because the HPC area pin of FMS on Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:

		+	*Remove the resistor for switch and button functions
		+	*:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver
	<noinclude>		<noinclude>
	[[Category:F2G]]		[[Category:F2G]]
	</noinclude>		</noinclude>