TR10a-HL ENFAQ - Revision history

Admin at 06:42, 4 June 2020

2020-06-04T06:42:58Z

← Older revision		Revision as of 06:42, 4 June 2020
Line 6:		Line 6:
	#:'''Q:''' How to resolve the situation that the "Device Manager" in the Window doesn’t show the PCIe Device and the PCIe Driver can’t be installed after running the .bat file provided in the system CD under folder \Demonstrations\PCIe_Fundamental and re-starting the PC?		#:'''Q:''' How to resolve the situation that the "Device Manager" in the Window doesn’t show the PCIe Device and the PCIe Driver can’t be installed after running the .bat file provided in the system CD under folder \Demonstrations\PCIe_Fundamental and re-starting the PC?
	#:<span style="color:#0000ff;">'''A''': Try the following methods to adjust the testing steps:</span>		#:<span style="color:#0000ff;">'''A''': Try the following methods to adjust the testing steps:</span>
-	#:#<span style="color:#0000ff;">First, plug the TR10a-HL board into the PC’s PCIe ~~socket~~ and connect the board with external power supply; then power on the board. Finally, power on the PC. (Note: the external power supply mentioned here refers to the power supply included in the TR10a-HL kit, NOT the power supply of the PC.) </span>	+	#:#<span style="color:#0000ff;">First, plug the TR10a-HL board into the PC’s PCIe slot and connect the board with external power supply; then power on the board. Finally, power on the PC. (Note: the external power supply mentioned here refers to the power supply included in the TR10a-HL kit, NOT the power supply of the PC.) </span>
	#:#<span style="color:#0000ff;">Download the sof file by executing test.bat. Power off the PC after the download is completed. At this time, the TR10a-HL continues to stay powered-on because it is connected to an external power supply.</span>		#:#<span style="color:#0000ff;">Download the sof file by executing test.bat. Power off the PC after the download is completed. At this time, the TR10a-HL continues to stay powered-on because it is connected to an external power supply.</span>
-	#:#<span style="color:#0000ff;">Re-start the PC after it is completely power-off. The Device Manager will then show the PCIe ~~Device~~.</span>	+	#:#<span style="color:#0000ff;">Re-start the PC after it is completely power-off. The Device Manager will then show the PCIe device.</span>
		+	#
		+	#:'''Q:'''Does TR10a-HL board support OpenCL?
		+	#:<span style="color:#0000ff;">'''A''':The TR10a-HL does not support OpenCL for the time being, as it is not equipped with DDR3 or DDR4. That being said, Terasic’s some other Arria 10 FPGA based boards such as DE5a-Net-DDR4, HERO and HAN all support OpenCL.
	#		#
	#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?		#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?
Line 25:		Line 28:
	#:[[File:TR10a-HL.png]]		#:[[File:TR10a-HL.png]]
	#:<span style="color:#0000ff;"> Then use the .bat file under folder Demonstrations/Hello/flash_programming_batch to program Flash. If the name of the project is changed, users can modify the file content of flash_program.sh, and then run the .bat file to program Flash memory. </span>		#:<span style="color:#0000ff;"> Then use the .bat file under folder Demonstrations/Hello/flash_programming_batch to program Flash. If the name of the project is changed, users can modify the file content of flash_program.sh, and then run the .bat file to program Flash memory. </span>
		+
	<noinclude>		<noinclude>
	[[Category:ENFAQ]]		[[Category:ENFAQ]]
	[[Category:TR10a-HL]]		[[Category:TR10a-HL]]
	</noinclude>		</noinclude>

Admin at 02:32, 27 May 2020

2020-05-27T02:32:57Z

← Older revision		Revision as of 02:32, 27 May 2020
Line 12:		Line 12:
	#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?		#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?
	#:<span style="color:#0000ff;">'''A''':The three boards are all incorporated the same FPGA chip (10AX115N2F45E1SG) but the peripheral interface and the board size are different from one another. The below comparison tells their differences. </span>		#:<span style="color:#0000ff;">'''A''':The three boards are all incorporated the same FPGA chip (10AX115N2F45E1SG) but the peripheral interface and the board size are different from one another. The below comparison tells their differences. </span>
-	#:[[File:Tr10a hl faq compare.jpg]]	+	#:[[File:Tr10a hl faq compare.jpg\|800px]]
	#		#
	#:'''Q:''' What is the maximum power consumption of the TR10a-HL? What is the maximum speed supported by QSPF+?		#:'''Q:''' What is the maximum power consumption of the TR10a-HL? What is the maximum speed supported by QSPF+?

Admin at 02:32, 27 May 2020

2020-05-27T02:32:37Z

← Older revision		Revision as of 02:32, 27 May 2020
Line 12:		Line 12:
	#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?		#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?
	#:<span style="color:#0000ff;">'''A''':The three boards are all incorporated the same FPGA chip (10AX115N2F45E1SG) but the peripheral interface and the board size are different from one another. The below comparison tells their differences. </span>		#:<span style="color:#0000ff;">'''A''':The three boards are all incorporated the same FPGA chip (10AX115N2F45E1SG) but the peripheral interface and the board size are different from one another. The below comparison tells their differences. </span>
-	#:[[File:Tr10a hl faq ~~power~~.jpg]]	+	#:[[File:Tr10a hl faq compare.jpg]]
	#		#
	#:'''Q:''' What is the maximum power consumption of the TR10a-HL? What is the maximum speed supported by QSPF+?		#:'''Q:''' What is the maximum power consumption of the TR10a-HL? What is the maximum speed supported by QSPF+?

Admin at 02:07, 27 May 2020

2020-05-27T02:07:24Z

← Older revision		Revision as of 02:07, 27 May 2020
Line 25:		Line 25:
	#:[[File:TR10a-HL.png]]		#:[[File:TR10a-HL.png]]
	#:<span style="color:#0000ff;"> Then use the .bat file under folder Demonstrations/Hello/flash_programming_batch to program Flash. If the name of the project is changed, users can modify the file content of flash_program.sh, and then run the .bat file to program Flash memory. </span>		#:<span style="color:#0000ff;"> Then use the .bat file under folder Demonstrations/Hello/flash_programming_batch to program Flash. If the name of the project is changed, users can modify the file content of flash_program.sh, and then run the .bat file to program Flash memory. </span>
		+	<noinclude>
		+	[[Category:ENFAQ]]
		+	[[Category:TR10a-HL]]
		+	</noinclude>

Admin at 02:06, 27 May 2020

2020-05-27T02:06:47Z

← Older revision		Revision as of 02:06, 27 May 2020
Line 1:		Line 1:
	#		#
	#:'''Q:'''There are 6 pins on the TR10a-HL external power connector, which pin are 12V power and which are ground? Is there a required sequence of external power supply and PCIe power supply?		#:'''Q:'''There are 6 pins on the TR10a-HL external power connector, which pin are 12V power and which are ground? Is there a required sequence of external power supply and PCIe power supply?
-	#:<span style="color:#0000ff;">'''A''':Please refer to the figure below to see which 3 pins are 12V and GND pin. You can choose either the external power supply or the PCIe power supply. No sequence for power supply is required. If power is supplied at the same time, the board itself will automatically switch to external power supply </span>	+	#:<span style="color:#0000ff;">'''A''':Please refer to the figure below to see which 3 pins are 12V and which 3 are GND pin. You can choose either the external power supply or the PCIe power supply. No sequence for power supply is required. If power is supplied at the same time, the board itself will automatically switch to external power supply </span>
	#:[[File:Tr10a hl faq power.jpg]]		#:[[File:Tr10a hl faq power.jpg]]
	#		#

Admin at 02:06, 27 May 2020

2020-05-27T02:06:05Z

← Older revision		Revision as of 02:06, 27 May 2020
Line 24:		Line 24:
	#:<span style="color:#0000ff;">'''A''': First, please make sure if the base address setting of CFI Flash in Qsys as well as its corresponding reset vector setting are correct or not. The correct setting should be as follows. </span>		#:<span style="color:#0000ff;">'''A''': First, please make sure if the base address setting of CFI Flash in Qsys as well as its corresponding reset vector setting are correct or not. The correct setting should be as follows. </span>
	#:[[File:TR10a-HL.png]]		#:[[File:TR10a-HL.png]]
		+	#:<span style="color:#0000ff;"> Then use the .bat file under folder Demonstrations/Hello/flash_programming_batch to program Flash. If the name of the project is changed, users can modify the file content of flash_program.sh, and then run the .bat file to program Flash memory. </span>

Admin at 02:04, 27 May 2020

2020-05-27T02:04:47Z

← Older revision		Revision as of 02:04, 27 May 2020
Line 23:		Line 23:
	#:<span style="color:#00aa00;">Leaving target processor paused"		#:<span style="color:#00aa00;">Leaving target processor paused"
	#:<span style="color:#0000ff;">'''A''': First, please make sure if the base address setting of CFI Flash in Qsys as well as its corresponding reset vector setting are correct or not. The correct setting should be as follows. </span>		#:<span style="color:#0000ff;">'''A''': First, please make sure if the base address setting of CFI Flash in Qsys as well as its corresponding reset vector setting are correct or not. The correct setting should be as follows. </span>
-	~~#:[[File:TR10a-HL.png]]~~
	#:[[File:TR10a-HL.png]]		#:[[File:TR10a-HL.png]]

Admin at 02:04, 27 May 2020

2020-05-27T02:04:39Z

← Older revision		Revision as of 02:04, 27 May 2020
Line 23:		Line 23:
	#:<span style="color:#00aa00;">Leaving target processor paused"		#:<span style="color:#00aa00;">Leaving target processor paused"
	#:<span style="color:#0000ff;">'''A''': First, please make sure if the base address setting of CFI Flash in Qsys as well as its corresponding reset vector setting are correct or not. The correct setting should be as follows. </span>		#:<span style="color:#0000ff;">'''A''': First, please make sure if the base address setting of CFI Flash in Qsys as well as its corresponding reset vector setting are correct or not. The correct setting should be as follows. </span>
		+	#:[[File:TR10a-HL.png]]
		+	#:[[File:TR10a-HL.png]]

Admin at 02:04, 27 May 2020

2020-05-27T02:04:05Z

← Older revision		Revision as of 02:04, 27 May 2020
Line 12:		Line 12:
	#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?		#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?
	#:<span style="color:#0000ff;">'''A''':The three boards are all incorporated the same FPGA chip (10AX115N2F45E1SG) but the peripheral interface and the board size are different from one another. The below comparison tells their differences. </span>		#:<span style="color:#0000ff;">'''A''':The three boards are all incorporated the same FPGA chip (10AX115N2F45E1SG) but the peripheral interface and the board size are different from one another. The below comparison tells their differences. </span>
		+	#:[[File:Tr10a hl faq power.jpg]]
		+	#
		+	#:'''Q:''' What is the maximum power consumption of the TR10a-HL? What is the maximum speed supported by QSPF+?
		+	#:<span style="color:#0000ff;">'''A''': The maximum power consumption of TR10a-HL is about 80W; the maximum speed supported by QSPF+ is 40G.</span>
		+	#
		+	#:'''Q:''' What to do if the following message shows up when programming Flash by using Quartus 18.1 to execute the command “nios2-flash-programmer” on TR10a-HL?
		+	#:<span style="color:#00aa00;">"Checksummed/read 108kB in 0.0s
		+	#:<span style="color:#00aa00;">02B40000 ( 0%): Erasing
		+	#:<span style="color:#00aa00;">Erase failed at offset 2B40000
		+	#:<span style="color:#00aa00;">Leaving target processor paused"
		+	#:<span style="color:#0000ff;">'''A''': First, please make sure if the base address setting of CFI Flash in Qsys as well as its corresponding reset vector setting are correct or not. The correct setting should be as follows. </span>

Admin at 01:59, 27 May 2020

2020-05-27T01:59:21Z

← Older revision		Revision as of 01:59, 27 May 2020
Line 9:		Line 9:
	#:#<span style="color:#0000ff;">Download the sof file by executing test.bat. Power off the PC after the download is completed. At this time, the TR10a-HL continues to stay powered-on because it is connected to an external power supply.</span>		#:#<span style="color:#0000ff;">Download the sof file by executing test.bat. Power off the PC after the download is completed. At this time, the TR10a-HL continues to stay powered-on because it is connected to an external power supply.</span>
	#:#<span style="color:#0000ff;">Re-start the PC after it is completely power-off. The Device Manager will then show the PCIe Device.</span>		#:#<span style="color:#0000ff;">Re-start the PC after it is completely power-off. The Device Manager will then show the PCIe Device.</span>
		+	#
		+	#:'''Q:''' What are the differences among TR10a-HL, TR10a-HL2 and TR10-LPQ?
		+	#:<span style="color:#0000ff;">'''A''':The three boards are all incorporated the same FPGA chip (10AX115N2F45E1SG) but the peripheral interface and the board size are different from one another. The below comparison tells their differences. </span>