Altera USB Blaster Driver Installation Instructions
From Terasic Wiki
(Difference between revisions)
(→For Windows 10, do the following:) |
(→For Windows 10, do the following:) |
||
| (7 intermediate revisions not shown) | |||
| Line 2: | Line 2: | ||
==For Windows 10, do the following:== | ==For Windows 10, do the following:== | ||
# Plug the USB-Blaster into your PC. | # Plug the USB-Blaster into your PC. | ||
| - | # | + | # Open the Device and Printers (Control Panel | Devices and Printers). |
| - | # | + | # Under Unspecified, USB Blaster should be listed. Right mouse click on this and then select Properties. |
| - | # | + | # Select the Hardware tab and select Properties. |
| - | # | + | # A new window should pop up with the General tab already selected. Select Change Settings. |
| - | # | + | # Again a new window should pop up with the General tab already selected. Select Update. |
| - | # | + | # Select Browse my computer for driver software. |
| - | # | + | # Find <Path to Quartus II installation>\quartus\drivers\ |
| - | + | *(Note 1: Your altera file is located at the location you selected when you first installed quartus. The location listed in this document is the default location) | |
| - | + | *(Note 2: Stop at the drivers folder, i.e., do NOT go deeper by opening a folder within the drivers folder) | |
# Select OK. Make sure the proper path was selected then select Next. | # Select OK. Make sure the proper path was selected then select Next. | ||
# If the Windows security window pops up Check the Always trust software from “Altera Corporation”box and select Install. | # If the Windows security window pops up Check the Always trust software from “Altera Corporation”box and select Install. | ||
| Line 21: | Line 21: | ||
# Under Other devices, USB Blaster should be listed. Right mouse click on this and then select Update Driver Software… | # Under Other devices, USB Blaster should be listed. Right mouse click on this and then select Update Driver Software… | ||
# Select Browse my computer for driver software | # Select Browse my computer for driver software | ||
| - | # Find | + | # Find <Path to Quartus II installation>\quartus\drivers\, then select Next; (Note: Stop at this folder, i.e., do NOT go deeper by opening a folder within the drivers folder) |
# Check the Always trust … box and then select Install | # Check the Always trust … box and then select Install | ||
| + | |||
==For Windows Vista, do the following:== | ==For Windows Vista, do the following:== | ||
# Plug the USB-Blaster download cable into the PC. The Found New Hardware dialog box appears. | # Plug the USB-Blaster download cable into the PC. The Found New Hardware dialog box appears. | ||
| Line 49: | Line 50: | ||
**Scroll down to “Disable Driver Signature Enforcement,” then hit Enter. | **Scroll down to “Disable Driver Signature Enforcement,” then hit Enter. | ||
You must set up the driver before programming your PLD (CPLD or FPGA) | You must set up the driver before programming your PLD (CPLD or FPGA) | ||
| + | ==Driver== | ||
| + | [[:file:Usb blaster q16.1.zip|USB Blaster Drvier From Q16.1]] | ||
| - | [https://mil.ufl.edu/3701/docs/quartus/byteblaster/usb-blaster_driver_install.pdf| Reference by Dr. Eric M. Schwartz] | + | ==Reference== |
| + | *[https://mil.ufl.edu/3701/docs/quartus/byteblaster/usb-blaster_driver_install.pdf| Reference by Dr. Eric M. Schwartz] | ||
| + | *[[Terasic_USB_Blaster_Document|Back]] | ||
Latest revision as of 10:33, 9 May 2017
To install the driver for your USB Blaster cable, follow the instruction for your particular operating system.
Contents |
For Windows 10, do the following:
- Plug the USB-Blaster into your PC.
- Open the Device and Printers (Control Panel | Devices and Printers).
- Under Unspecified, USB Blaster should be listed. Right mouse click on this and then select Properties.
- Select the Hardware tab and select Properties.
- A new window should pop up with the General tab already selected. Select Change Settings.
- Again a new window should pop up with the General tab already selected. Select Update.
- Select Browse my computer for driver software.
- Find <Path to Quartus II installation>\quartus\drivers\
- (Note 1: Your altera file is located at the location you selected when you first installed quartus. The location listed in this document is the default location)
- (Note 2: Stop at the drivers folder, i.e., do NOT go deeper by opening a folder within the drivers folder)
- Select OK. Make sure the proper path was selected then select Next.
- If the Windows security window pops up Check the Always trust software from “Altera Corporation”box and select Install.
For Windows 7 and Windows 8, do the following:
- Plug the USB-Blaster download cable into the PC. The following will appear on the screen: Device driver software was not successfully install. Select Click here for details.
- Select Change settings…
- Now cancel this (probably by selecting Cancel)
- Open the Device Manager (Windows Key | Control Panel | Device Manage)
- Under Other devices, USB Blaster should be listed. Right mouse click on this and then select Update Driver Software…
- Select Browse my computer for driver software
- Find <Path to Quartus II installation>\quartus\drivers\, then select Next; (Note: Stop at this folder, i.e., do NOT go deeper by opening a folder within the drivers folder)
- Check the Always trust … box and then select Install
For Windows Vista, do the following:
- Plug the USB-Blaster download cable into the PC. The Found New Hardware dialog box appears.
- Select Locate and install driver software (recommended).
- Select Don't search online.
- When you are prompted to Insert the disc that came with your USB-Blaster, select I don’t have the disc. Show me other options.
- Select Browse my computer for driver software (advanced) when you see the Windows couldn’t find driver software for your device.
- Click Browse... and browse to the <Path to Quartus II installation>\drivers\usb-blaster directory. Click OK.
- Select the Include subfolders option and click Next.
- If you are prompted Windows can’t verify the publisher of this driver software, select Install this driver software anyway in the Window Security dialog box.
- The installation begins.
- When The software for this device has been successfully installed appears, click Close.
For Windows XP, do the following:
- Plug the USB-Blaster download cable into the PC. The Found New Hardware dialog box appears.
- Select Locate and install driver software (recommended).
- Select Don't search online.
- When you are prompted to Insert the disc that came with your USB-Blaster, select I don’t have the disc. Show me other options.
- Select Browse my computer for driver software (advanced) when you see the Windows couldn’t find driver software for your device.
- Click Browse... and browse to the <Path to Quartus II installation>\drivers\usb-blaster directory. Click OK.
- Select the Include subfolders option and click Next.
- If you are prompted Windows can’t verify the publisher of this driver software, select Install this driver software anyway in the Window Security dialog box.
- The installation begins.
When The software for this device has been successfully installed appears, click Close. If you are running Windows in 64-bit mode, you MUST boot your computer as following both when installing the USB-Blaster driver AND when using Quartus to program your PLD.
- During boot up of the computer, continuously press F8 (but do NOT hold it down).
- Scroll down to “Disable Driver Signature Enforcement,” then hit Enter.
You must set up the driver before programming your PLD (CPLD or FPGA)
