Can't download .sof file

From Terasic Wiki

(Difference between revisions)
Jump to: navigation, search
(Created page with "'''Can't download .sof file''' #'Programmer找不到端口导致.sof文件无法下载' 解决办法link 到《Programmer检测不到USB Blaster》网页。 2. Programmer找得...")
(→Can't download .sof file)
 
(9 intermediate revisions not shown)
Line 1: Line 1:
-
'''Can't download .sof file'''
 
-
#'Programmer找不到端口导致.sof文件无法下载'
+
'''1. Can't download .sof file as Hardward port couldn't been found in Programmer window'''
-
解决办法link 到《Programmer检测不到USB Blaster》网页。
+
-
2. Programmer找得到端口，但是下载到一定进度显示失败：
+
Solution:[[No USB Blaster port is detected in Programmer window]]。
-
a. 查看RUN/PROG开关的设置是否正确。（请设置到RUN 模式）
+
-
b.请注意FPGA主板的jtag链回环。如果没有接子卡 ， 注意开发板上的对应跳线帽接法，让jtag链形成回环。
+
-
c.查看Programmer的Mode 设置是否正确。（请设置到jtag mode）
+
-
#Plug the USB-Blaster II cable into your PC.
+
'''2. Programmer window can detect USB Blaster port, but download progress bar presents "Failed"'''
-
#Open the '''Device Manager''', and right-click on the '''Unknown device''' under the '''Other devices''' branch.
+
-
#Select '''Update Driver Software'''.
+
-
#elect '''Browse my computer for driver software'''.
+
-
#Enter the location of the Quartus Prime software USB-Blaster II driver files directory ('''<Path to Quartus Prime installation>\drivers\usb-blaster-ii''') in the '''Search for driver software in this location''' field.
+
-
#Click '''Next'''.
+
-
#Click '''Install''' in the '''Would you like to install this device software'''? Windows security dialog box.
+
-
#Close the '''Update Driver Software - Altera USB-Blaster II (Unconfigured)'''successful installation notification. The Device Manager now shows a new branch called '''JTAG cables''' with an '''Altera USB-#Blaster II (Unconfigured)''' node.
+
-
#Open the Quartus Prime Programmer. Within a few seconds, the '''JTAG cables''' branch displays two nodes: '''Altera USB-Blaster II (JTAG interface)''' and '''Altera-USB Blaster II (System Console interface)'''.
+
-
[[Terasic_USB_Blaster_Document|Back]]
+
a. Check switch RUN/PROG setting is correct or not(Please set it to RUN mode).
 +
 
 +
b.Please make sure the board jtag circuit is in loopback state. For example, if you connect a daughter card on HSMC connector, you need check the board corresponding jumper setting.
 +
 
 +
c.Check the Programmer window Mode setting is correct or not(set Mode to Jtag).
 +
 
 +
 
 +
[[Terasic Accessory|back]]

Latest revision as of 11:29, 18 April 2017

1. Can't download .sof file as Hardward port couldn't been found in Programmer window

Solution:No USB Blaster port is detected in Programmer window。


2. Programmer window can detect USB Blaster port, but download progress bar presents "Failed"

a. Check switch RUN/PROG setting is correct or not(Please set it to RUN mode).

b.Please make sure the board jtag circuit is in loopback state. For example, if you connect a daughter card on HSMC connector, you need check the board corresponding jumper setting.

c.Check the Programmer window Mode setting is correct or not(set Mode to Jtag).


back

Retrieved from "http://www.terasic.com.tw/wiki/Can%27t_download_.sof_file"