PCA3 User Manual
From Terasic Wiki
(Difference between revisions)
(Created page with ":{| class="wikitable" |- !rowspan="2"|Pin Numbers !!colspan="2"|Side B !!colspan="2"|Side A |- ! |Name ||Description||Name ||Description |- |1 ||NC ||NC ||PRSNT1n ||Hot-Plug ...") |
|||
Line 1: | Line 1: | ||
- | + | =Chapter 1 Introduction= | |
- | + | The Terasic PCIe x4 Cable Adapter (PCA3) is used to connect a PCIe upstream slot with downstream target board via PCIe x4 cable, supporting PCIe x4 & x1 lanes. The PCA3 can provide programmable equalization, amplification, and de-emphasis for PCIe transceiver signal by using 8 select bits. It is also available to optimize performance over a variety of physical mediums by reducing Inter-symbol interference. | |
- | + | ||
- | + | ==Features== | |
- | + | Figure 1-1 shows a photograph of the PCA3 card.<br/> | |
- | + | ::::[[File:PCA3 Exterior View.jpg|350px]]<br/> | |
- | + | :::::::Figure 1-1 Exterior View<br/> | |
- | + | The key features of the card are listed below:<br/> | |
- | + | :*Up to 8.0Gbps PCIe 3.0 Serial Re-Driver | |
- | + | :*PCIe x4 Gen 3 | |
- | + | :*Adjustable receiver equalization | |
- | + | :*Adjustable transmitter amplitude and de-emphasis | |
- | + | ||
- | + | ==Getting Help== | |
- | + | Here is information of how to get help if you encounter any problem:<br/> | |
- | + | Terasic Technologies<br/> | |
- | + | :*Tel: +886-3-550-8800 | |
- | + | :*Email: support@terasic.com.cn | |
- | + | ||
- | + | =Chapter 2 Architecture= | |
- | + | This chapter provides information about architecture and block diagram of the PCA3 board. | |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | | | + | |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + |
Revision as of 15:10, 20 October 2017
Contents |
Chapter 1 Introduction
The Terasic PCIe x4 Cable Adapter (PCA3) is used to connect a PCIe upstream slot with downstream target board via PCIe x4 cable, supporting PCIe x4 & x1 lanes. The PCA3 can provide programmable equalization, amplification, and de-emphasis for PCIe transceiver signal by using 8 select bits. It is also available to optimize performance over a variety of physical mediums by reducing Inter-symbol interference.
Features
Figure 1-1 shows a photograph of the PCA3 card.
The key features of the card are listed below:
- Up to 8.0Gbps PCIe 3.0 Serial Re-Driver
- PCIe x4 Gen 3
- Adjustable receiver equalization
- Adjustable transmitter amplitude and de-emphasis
Getting Help
Here is information of how to get help if you encounter any problem:
Terasic Technologies
- Tel: +886-3-550-8800
- Email: support@terasic.com.cn
Chapter 2 Architecture
This chapter provides information about architecture and block diagram of the PCA3 board.