USB Blaster Self Test

From Terasic Wiki

(Difference between revisions)
Jump to: navigation, search
Line 1: Line 1:
-
'''這份文件將引導使用者如何檢測 On-Board usb blaster或者USB Blaster Cable是否驅動程式正常安裝並運作. '''
+
'''This document describes users how to test whether the on-board USB blaster or USB blaster cable is properly installed and operated.'''
-
#將FPGA Board電源開啟並將USB Blaster port或者USB Blaster Cable與PC連接,簡查是否Windows的Device Manger裡面的Universal Serial Bus controller是否有出現Altera USB Blaster,如果有Quartus Programmer便可以正常使用下載FPGA code<br/>[[File:Device Manger.png]]
+
#Power on the FPGA board and connect USB blaster port or USB blaster cable to PC. <br/>Check if the Universal Serial Bus controller in the Windows Device Manger has an Altera USB Blaster.<br/>If yes, users can use Quartus programmer and download FPGA code.<br/>[[File:Device Manger.png]]
-
#若是Universal Serial Bus controller沒有出現Altera USB Blaster,請檢查是否Other Device內有出現Unkown device<br/>[[File:Device Manger2.png]].<br/>若是有,請參照下面的連結,安裝 USB Blaster Driver .[http://www.terasic.com.tw/wiki/Altera_USB_Blaster_Driver_Installation_Instructions Altera USB Blaster Driver Installation Instructions]
+
#If Altera USB Blaster isn’t showed in Universal Serial Bus controller, please check whether the Other Device has Unknown device.<br/>[[File:Device Manger2.png]].<br/>If yes, please install the USB blaster driver refer to this link:[http://www.terasic.com.tw/wiki/Altera_USB_Blaster_Driver_Installation_Instructions Altera USB Blaster Driver Installation Instructions]
-
#如果沒有出現 Unkown Device:
+
#If no unknown device:
-
::i.確認是否板子電源有開啟 ,並且確認與PC連接的是 USB Blaster port
+
::i.Make sure the board power is on and the port on board which connected to PC is USB blaster port.
-
::ii.如果確認i的步驟沒有問題:
+
::ii.If step i is OK:
-
:::a.更換另一台電腦連接看看,是否操作系統有偵測到unknown devce
+
:::a.Test with another PC to see if the OS can detect unknown device
-
:::b.更換一條 usb cable<br/>[[File:Usb cable.png]]<br/>
+
:::b.Test with another usb blaster cable<br/>[[File:Usb cable.png]]<br/>
-
:::c.若以上還是不行,請聯絡我門技術支持 support@terasic.com,並請提供以下資料:
+
:::c.If still with the same problem, please contact our technical support team via supprot@terasic.com and provide below information:
-
::::*操作系統版本: Win10-32bit or Win7-64bit or Linux-64bit
+
::::*PC OS version: Win10 -32bit or Win7-64bit or Linux-64bit  
-
::::*是否已經照本流程檢測過?
+
::::*Whether you tested follow the above process
-
::::*安裝的Quartus version,EX:Q16.1
+
::::*The Quartus version you in stalled: Q16.1 or others

Revision as of 11:00, 7 April 2017

This document describes users how to test whether the on-board USB blaster or USB blaster cable is properly installed and operated.

  1. Power on the FPGA board and connect USB blaster port or USB blaster cable to PC.
    Check if the Universal Serial Bus controller in the Windows Device Manger has an Altera USB Blaster.
    If yes, users can use Quartus programmer and download FPGA code.
    Device Manger.png
  2. If Altera USB Blaster isn’t showed in Universal Serial Bus controller, please check whether the Other Device has Unknown device.
    Device Manger2.png.
    If yes, please install the USB blaster driver refer to this link:Altera USB Blaster Driver Installation Instructions
  3. If no unknown device:
i.Make sure the board power is on and the port on board which connected to PC is USB blaster port.
ii.If step i is OK:
a.Test with another PC to see if the OS can detect unknown device
b.Test with another usb blaster cable
Usb cable.png
c.If still with the same problem, please contact our technical support team via supprot@terasic.com and provide below information:
  • PC OS version: Win10 -32bit or Win7-64bit or Linux-64bit
  • Whether you tested follow the above process
  • The Quartus version you in stalled: Q16.1 or others
Retrieved from "http://www.terasic.com.tw/wiki/USB_Blaster_Self_Test"