Adapters
- 9VDC switching supply with 1.3A current
- Output: AC 100V~240V (50/60Hz)
- Compatibility:DE2
- 9VDC switching supply with 1.3A current
- Input: AC 100~240V (50/60Hz)
- Output: DC 9V/1.3A
- Size: 60.2*44*26.2 mm
- Compatibility: DE2
- 7.5VDC switching supply with 0.8A current
- Output: AC 100~240V (50/60Hz)
- Input: DC 7.5V/0.8A
- Size: 44*32*23.5 mm
- Compatibility: DE0 / DE1 / Cyclone II Starter Kit
- 9VDC switching supply with 2.6A current
- Input: AC 100V~240V (50/60Hz)
- Output: DC 9V/2.6A
- Compatibility: TREX-S2 Stratix II FPGA Prototyping System
- Rating: 2.5A / 250V
- Length: 1.8M
- Convenient way to switch from US wall plugs to EURO wall plugs
- Compatibility: VEEK-MT-C5SoC / DE1-SoC / C5G
- 250V/16A
- Convenient way to switch from US wall plugs to EU wall plugs
- Simple snap-on design used with Terasic Technologies's switching power supplies
Cables
- The cable is 20 cm long.
- Turn your DE10-Nano into a USB host via the OTG port onboard.
- Allow you to connect USB accessories such as Flash drive, keyboard, mouse, camera, Bluetooth or Wi-Fi module to your DE10-Nano .
- x4 PCIe connector on both ends
- Supports x4 PCIe data bus
- Compatible with TR4 FPGA Development Kit
- 1 meter (3.28 feet) / 2 meter (6.56 feet) / 3 meter (9.84 feet)
- Spec: HSTC female connector at both ends
- Size: 12 inches (304.80 mm)
- Compatibility: Only for two DE3 board connection
- Spec: HSMC male connector at both ends
- Size: 12 inches (304.80 mm)
- Compatibility: DE2-115, DE4 & Host boards which supporting HSMC-compliant connectors
- Connector: DB9M/DB9F
- Length: 1.8M
- For serial communications
- Compatibility: TREX-C1
Extras
- 16 Megapixel: 2 times higher res, half the cost.
- PDAF Breakthrough: Adopts the Mixture of PDAF and CDAF
- achieves the unity of focusing speed and precision.
- Sharper Images/videos: Higher quality than the HQ camera.
- V1/V2 Size: hassle-free upgrades to your existing projects.
- Open Source: truly accessible to all.
- VITA 57.4 FMC+ or Vita57.1 FMC form factor
- Mates with HPC or LPC carrier boards
- Ultra-Low Jitter Clock Multiplier for clock testing
- OCXO Clock Source
- SMA Interface
- Powered from 2x5 JTAG Header
- 1PPS and 10MHz Clocks Distributor
- UART to USB
- Powered from 2x5 Expansion Header
- Bluetooth v 4.0+EDR
- Class 1, wireless range of up to 50m
- Compliant to Atum A5 、 DE25-Standard 、 MA27 、 DE10-Standard and DE10-Nano Linux BSP
- Type: WiFi USB Dongle
- WIFI Transmission Protocol: 802.11b/n/g
- Transmission Rate: 150Mbps
- Interface: USB 2.0
- Rechargeable battery
- Fully charged in 2 hours
- Under constant operation, the battery charge will last approximately 25 minutes
- Compatibility: DE2-115, DE4, TR4, and other host boards which supporting HSMC-compliant connectors
A 160-pin high speed connector which is gives users more flexibility when utilizing the interfaces of HSMC connector.
- Form-fitting tPad/VEEK-MT/VEEK-MT2 dimensions.
- Shock-absorbing and water-proof fabric exterior
- Front pocket for pens, memory cards, cellphones, etc.
This package consists of HSMC adapters that are intended for testing and debugging purposes over the High-Speed Mezzanine card (HSMC). The package includes two loopback high-speed mezzanine connector (HSMC) cards and a debug HSMC card which can be connected to any HSMC interface.
- Compatibility: Any HSMC-based host board
HSMC Flex Cable is equipped with two 160-pin HSMC connectors, one male and female each. It allows user to connect 2 HSMC-interfaced boards together. For example, a Cyclone III Starter Kit is connected to NEEK Upgrade Kit in a brick form by this cable.
- Compatibility: Multimedia-HSMC Card / Cyclone III Starter Kit
- 1.3 Mega Pixel
- Compatibility: DC2
- Including six silicon footstands
- Including two cables(black- and red-colored)
- two pins to be used together for testing FPGA boards
- Compatibility: DE2-70 / DE2 / DE1 / Cyclone II Starter Kit