F2G with intel A10GFP
From Terasic Wiki
(→GPIO Using Status) |
(→Other considerations) |
||
| (10 intermediate revisions not shown) | |||
| Line 10: | Line 10: | ||
| - | On the Kit board, some FPGA I/Os connected to the F2G GPIO connector will have termination resistors(for differential protocol). It is recommended to remove these resistors, otherwise the pins of the GPIO connector will interfere with each other when using in single-end state. <span style="color:#0000ff;"> When the F2G is conneted to the '''FMCA''' connector of the kit.'''Please remove R383,R369 and R336 on the Arria® 10 GX FPGA Development Kit.''' When the F2G is conneted to the '''FMCB''' connector of the kit, please remove '''R349,R333 and R379'''.</span> | + | On the Arria® 10 GX FPGA Development Kit board, some FPGA I/Os connected to the F2G GPIO connector will have termination resistors(for differential protocol). It is recommended to remove these resistors, otherwise the pins of the GPIO connector will interfere with each other when using in single-end state. <span style="color:#0000ff;"> When the F2G is conneted to the '''FMCA''' connector of the kit.'''Please remove R383,R369 and R336 on the Arria® 10 GX FPGA Development Kit.''' When the F2G is conneted to the '''FMCB''' connector of the kit, please remove '''R349,R333 and R379'''.</span> |
| Line 29: | Line 29: | ||
= Other considerations = | = Other considerations = | ||
| - | Because the HPC area pin of | + | Because the HPC area pin of FMC on Arria® 10 GX FPGA Development Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions: |
| + | *Remove the resistors for switch and button functions | ||
| + | *:Please remove '''RN1, R18 and R19''' for for disconnecting these functions from the FPGA transciver. | ||
| + | <div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 04.jpg|1200px]]</div> | ||
| + | |||
| + | *Remove the resistors for TMD header functions | ||
| + | *:Please remove '''R4 ~ R11''' for for disconnecting these functions from the FPGA transciver. | ||
| + | <div style="text-align:center;color:#ff0000;"> [[Image: F2g a10gfp 05a.jpg|800px]]</div> | ||
<noinclude> | <noinclude> | ||
[[Category:F2G]] | [[Category:F2G]] | ||
| + | [[Category:FAQ]] | ||
</noinclude> | </noinclude> | ||
Latest revision as of 14:50, 1 September 2020
This document will introduce what you need to pay attention to when the Terasic F2G card is connected to Intel Arria® 10 GX FPGA Development Kit.
GPIO Using Status
Due the two FMC connectors FMCA and FMCB on the Arria® 10 GX FPGA Development Kit belong to the low pin count(LPC) FMC type(Note), after connecting the F2G card, only the two connectors GPIO 0 and GPIO 1 on the F2G card can be used on the kit, and the other two GPIO connectors are defined Connected to high pin count(HPC) FMC pin, so it cannot be used in the kit. In addition, the D8/D9 pin on GPIO 1 belongs to the HPC FMC area, so it cannot be used.
On the Arria® 10 GX FPGA Development Kit board, some FPGA I/Os connected to the F2G GPIO connector will have termination resistors(for differential protocol). It is recommended to remove these resistors, otherwise the pins of the GPIO connector will interfere with each other when using in single-end state. When the F2G is conneted to the FMCA connector of the kit.Please remove R383,R369 and R336 on the Arria® 10 GX FPGA Development Kit. When the F2G is conneted to the FMCB connector of the kit, please remove R349,R333 and R379.
| Connector | Resistors needed to be removed |
|---|---|
| FMCA | R383,R369 and R336 |
| FMCB | R349,R333 and R379 |
Other considerations
Because the HPC area pin of FMC on Arria® 10 GX FPGA Development Kit is connected with the transciver of FPGA. These FMC pins are also connected with some I/O of Switch, Button and TMD header on F2G card. In order to prevent the abnormality of transciver channel of FPGA, users are advised to remove the following components on the F2G card to disable the these functions:
- Remove the resistors for switch and button functions
- Please remove RN1, R18 and R19 for for disconnecting these functions from the FPGA transciver.
- Remove the resistors for TMD header functions
- Please remove R4 ~ R11 for for disconnecting these functions from the FPGA transciver.
