Accessories

Adapters

  • 12V DC switching supply with 2A current
  • Input : AC 100~240V 50/60Hz
  • Output : DC 12V/2A
  • Size: 98.4*45*31.4 mm
  • Compatibility: DE1-SoC / DE2-115 / DE2-70 / C5GNEEK

(Currency: USD)
$15

  • 9VDC switching supply with 1.3A current
  • Output: AC 100V~240V (50/60Hz)
  • Compatibility:DE2

(Currency: USD)
$11

  • 9VDC switching supply with 1.3A current 
  • Input: AC 100~240V (50/60Hz)
  • Output: DC 9V/1.3A
  • Size: 60.2*44*26.2 mm
  • Compatibility: DE2

(Currency: USD)
$10

  • 7.5VDC switching supply with 0.8A current
  • Output: AC 100~240V (50/60Hz)
  • Input: DC 7.5V/0.8A
  • Size: 44*32*23.5 mm
  • Compatibility:  DE0 / DE1 / Cyclone II Starter Kit  

(Currency: USD)
$8

(Currency: USD)
$17

  • Rating: 2.5A / 250V
  • Length: 1.8M
  • Convenient way to switch from US wall plugs to EURO wall plugs
  • Compatibility:  VEEK-MT-C5SoC / DE1-SoC / C5G

(Currency: USD)
$3

(Currency: USD)
$4.5

  • 250V/16A
  • Convenient way to switch from US wall plugs to EU wall plugs
  • Simple snap-on design used with Terasic Technologies's switching power supplies

(Currency: USD)
$3

  • 250V / 5A
  • Convenient way to switch from US wall plugs to UK wall plugs
  • Simple snap-on design used with Terasic Technologies's switching power supplies
  • Compatibility: DE10-Nano / DE0 / DE2-115 / C5G / DE1-SoC  

(Currency: USD)
$4

Cables

  • The cable is 20 cm long.
  • Turn your DE10-Nano into a USB host via the OTG port onboard.
  • Allow you to connect USB accessories such as Flash drive, keyboard, mouse, camera, Bluetooth or Wi-Fi module to your DE10-Nano .

Contact Us

  • x4 PCIe  connector on both ends
  • Supports x4 PCIe data bus
  • Compatible with TR4 FPGA Development Kit
  • 1 meter (3.28 feet) / 2 meter (6.56 feet) /  3 meter (9.84 feet)

(Currency: USD)
$55

  • Spec: HSTC female connector at both ends
  • Size: 12 inches (304.80 mm)
  • Compatibility: Only for two DE3 board connection

 

(Currency: USD)
$310

  • Spec: HSMC male connector at both ends
  • Size: 12 inches (304.80 mm)
  • Compatibility: DE2-115, DE4 & Host boards which supporting HSMC-compliant connectors

(Currency: USD)
$310

(Currency: USD)
$3

  • Connector: DB9M/DB9F
  • Length: 1.8M
  • For serial communications
  • Compatibility: TREX-C1

(Currency: USD)
$2

Extras

  • 16 Megapixel: 2 times higher res, half the cost.
  • PDAF Breakthrough: Adopts the Mixture of PDAF and CDAF
  • achieves the unity of focusing speed and precision.
  • Sharper Images/videos: Higher quality than the HQ camera.
  • V1/V2 Size: hassle-free upgrades to your existing projects.
  • Open Source: truly accessible to all.

(Currency: USD)
$39

  • VITA 57.4 FMC+ or Vita57.1 FMC form factor
  • Mates with HPC or LPC carrier boards
  • Ultra-Low Jitter Clock Multiplier for clock testing

(Currency: USD)
$199

  • OCXO Clock Source
  • SMA Interface
  • Powered from 2x5 JTAG Header

(Currency: USD)
$255

  • 1PPS and 10MHz Clocks Distributor
  • UART to USB
  • Powered from 2x5 Expansion Header

 

(Currency: USD)
$150

(Currency: USD)
$15

  • Type: WiFi USB Dongle
  • WIFI Transmission Protocol: 802.11b/n/g
  • Transmission Rate: 150Mbps
  • Interface: USB 2.0

(Currency: USD)
$8

  • Rechargeable battery
  • Fully charged in 2 hours
  • Under constant operation, the battery charge will last approximately 25 minutes

(Currency: USD)
$40

  • Compatibility: DE2-115, DE4, TR4, and other host boards which supporting HSMC-compliant connectors

(Currency: USD)
$45

A 160-pin high speed connector which is gives users more flexibility when utilizing the interfaces of HSMC connector.

(Currency: USD)
$50

  • Form-fitting tPad/VEEK-MT/VEEK-MT2 dimensions. 
  • Shock-absorbing and water-proof fabric exterior
  • Front pocket for pens, memory cards, cellphones, etc.

(Currency: USD)
$10

This package consists of HSMC adapters that are intended for testing and debugging purposes over the High-Speed Mezzanine card (HSMC). The package includes two loopback high-speed mezzanine connector (HSMC) cards and a debug HSMC card which can be connected to any HSMC interface.

  • Compatibility: Any HSMC-based host board

 

(Currency: USD)
$99

HSMC Flex Cable is equipped with two 160-pin HSMC connectors, one male and female each. It allows user to connect 2 HSMC-interfaced boards together. For example, a Cyclone III Starter Kit is connected to NEEK Upgrade Kit in a brick form by this cable. 

(Currency: USD)
$35

Contact Us

  • 1.3 Mega Pixel
  • Compatibility: DC2

(Currency: USD)
$25

  • Including six silicon footstands
  • Including two cables(black- and red-colored)
  • two pins to be used together for testing FPGA boards
  • Compatibility: DE2-70 / DE2 / DE1 / Cyclone II Starter Kit

(Currency: USD)
$1