新聞訊息 關於友晶 產品資訊 解決方案 培訓與活動 FAQ
Cart
 
   
 
停產產品 母板 VEEK-MT-C5SoC
 





VEEK-MT-C5SoC

VEEK-MT-C5SoC

Cyclone V SX SoC Development Board

SoC Embedded Design Suite Subscription Edition

  • ARM Development Studio 5 (DS-5™) Altera Edition Toolkit
  • Hardware-to-software handoff tools
  • Linux run-time software for application development
  • SoC hardware libraries for firmware development
  • Application example

Cyclone V SX SoC—5CSXFC6D6F31C6N (SoC)

  • 110K LEs, 41509 ALMs
  • 5140 M10K memory blocks
  • 224 18x18 Multiplier
  • 6 FPGA PLLs and 3 HPS PLLs

Configuration Device and USB Blaster Circuit

  • Active Serial (AS) x1 or x4 configuration (EPCQ256SI16N)
  • MAX® V CPLD (5M2210ZF256I5N) in a 256-pin FBGA package as the System Controller
  • Flash fast passive parallel (FPP) configuration
  • MAX II CPLD (EPM570GM100) as part of the embedded USB-BlasterTM II for use with the Quartus® II Programmer

Memory Devices

  • One 1,024-Mbyte (MB) HPS DDR3 SDRAM with error correction code (ECC) support
  • One 1,024-MB FPGA DDR3 SDRAM
  • One 256-Megabit (Mb) quad serial peripheral interface (QSPI) flash
  • One 512-Mb CFI flash
  • One 32-Kb I2C serial electrically erasable PROM (EEPROM)
  • One Micro SD flash memory card

Switches and Indicators

  • LEDs and displays
    • Eight user LEDs
    • One configuration load LED
    • One configuration done LED
    • One error LED
    • Three configuration select LEDs
    • Four on-board USB-Blaster II status LEDs
    • One HSMC interface LED
    • Two UART data transmit and receive LEDs
    • One power on LED
    • One two-line character LCD display
  • Push buttons
    • One CPU reset push button
    • One MAX V reset push button
    • One program select push button
    • One program configuration push button
    • Six general user push buttons
  • DIP switches
    • One MAX V CPLD System Controller control switch
    • One JTAG chain control DIP switch
    • One mode select DIP switch
    • One general user DIP switch

On-board Clocking Circuitry

  • Si570, Si571, and Si5338 programmable oscillators
  • 25-MHz, 50-MHz,100-MHz, 125-MHz, 148.50-MHz, and 156.25-MHz oscillators
  • SMA input (LVCMOS)

Communication Ports

  • One PCI Express x4 Gen1 socket
  • One universal HSMC port
  • One USB 2.0 on-the-go (OTG) port
  • One Gigabit Ethernet port
  • Dual 10/100 Ethernet ports
  • One SDI port (option for SMA connection)
  • One controller area network (CAN) port
  • One RS-232 UART (through the mini-USB port)
  • One real-time clock

Power

  • 14–20-V (laptop) DC input

Mechanical

  • 5.2" × 8.2" rectangular form factor

Capacitive LCD Touch Screen

  • Equipped with an 7-inch Amorphous-TFT-LCD (Thin Film Transistor Liquid Crystal Display) module
  • Module composed of LED backlight
  • Support 24-bit parallel RGB interface
  • Converting the X/Y coordination of touch point to its corresponding digital data via the Touch controller

5-Megapixel Digital Image Sensor

  • Superior low-light performance
  • High frame rate
  • Global reset release, which starts the exposure of all rows simultaneously
  • Bulb exposure mode, for arbitrary exposure times
  • Snapshot-mode to take frames on demand
  • Horizontal and vertical mirror image
  • Column and row skip modes to reduce image size without reducing field-of-view
  • Column and row binning modes to improve image quality when resizing
  • Simple two-wire serial interface
  • Programmable controls: gain, frame rate, frame size, exposure

Digital Accelerometer

  • Up to 13-bit resolution at +/- 16g
  • SPI (3- and 4-wire) digital interface
  • Flexible interrupts modes

Ambient Light Sensor

  • Approximates human-eye response
  • Precise luminance measurement under diverse lighting conditions
  • Programmable interrupt function with user-defined upper and lower threshold settings
  • 16-bit digital output with I2C fast-mode at 400 kHz
  • Programmable analog gain and integration time
  • 50/60-Hz lighting ripple rejection

 



產品櫥窗 元件配置
新聞訊息 | 關於友晶 | 產品資訊 | 解決方案 | 培訓與活動 | FAQ | 聯絡我們 | 線上討論 | Facebook | YouTube