DE10-Advance Getting Start Guide revC
From Terasic Wiki
(Difference between revisions)
(→Chapter 1 About this guide) |
(→Chapter 5 Running Linux on the DE10-Advanced board via UART Terminal) |
||
| (3 intermediate revisions not shown) | |||
| Line 8: | Line 8: | ||
=Chapter 2 Development Board Setup= | =Chapter 2 Development Board Setup= | ||
| + | *[[DE10_Advance_Board Setup: Introduction| 2.1 Introduction]] | ||
| + | *[[DE10_Advance_Board Setup: MSEL Settings|2.2 MSEL Settings]] | ||
| + | *[[DE10_Advance_Board Setup: USB , Ethernet Port and Power Cables| 2.3 USB , Ethernet Port and Power Cables]] | ||
| + | *[[DE10_Advance_Board Setup: Power up the DE10-Advanced Board with LXDE VNC Desktop Environment| 2.4 Power up the DE10-Advanced Board with LXDE VNC Desktop Environment]] | ||
=Chapter 3 Software Installation= | =Chapter 3 Software Installation= | ||
| + | *[[DE10_Advance_Board Software Installation: Introduction| 3.1 Introduction]] | ||
| + | *[[DE10_Advance_Board Software Installation: Installing Quartus Prime software|3.2 Installing Quartus Prime software]] | ||
| + | *[[DE10_Advance_Board Software Installation: Installing Intel SoC Embedded Design Suite| 3.3 Installing Intel SoC Embedded Design Suite]] | ||
=Chapter 4 Performing a FPGA System Test= | =Chapter 4 Performing a FPGA System Test= | ||
| + | *[[DE10_Advance_Performing a FPGA System Test: Introduction| 4.1 Introduction]] | ||
| + | *[[DE10_Advance_Performing a FPGA System Test: Installing the USB-Blaster II Driver|4.2 Installing the USB-Blaster II Driver]] | ||
| + | *[[DE10_Advance_Performing a FPGA System Test: Downloading a FPGA SRAM Object File| 4.3 Downloading a FPGA SRAM Object File]] | ||
=Chapter 5 Running Linux on the DE10-Advanced board via UART Terminal= | =Chapter 5 Running Linux on the DE10-Advanced board via UART Terminal= | ||
| + | *[[DE10_Advance_Running Linux via UART Terminal: Introduction| 5.1 Introduction]] | ||
| + | *[[DE10_Advance_Running Linux via UART Terminal: Setting Up UART Terminal|5.2 Setting Up UART Terminal]] | ||
| + | *[[DE10_Advance_Running Linux via UART Terminal: Running Linux on DE10-Advanced board|5.3 Running Linux on DE10-Advanced board]] | ||
| + | *[[DE10_Advance_Running Linux via UART Terminal: Creating a MicroSD Card Image|5.4 Creating a MicroSD Card Image]] | ||
Latest revision as of 10:51, 30 August 2018
Contents |
Chapter 1 About this guide
The DE10-Advanced Getting Started Guide contains a quick overview of the hardware and software setup including step-by-step procedures from installing the necessary software tools to using the DE10-Advanced board. The main topics in this guide covers are listed below:
- Development Board Setup: Powering on the DE10-Advanced
- Software Installation: Installing Quartus Prime and SoC EDS
- Perform a FPGA System Test: Downloading a FPGA SRAM Object File (.sof)
- Running Linux on DE10- Advanced board via UART terminal
Chapter 2 Development Board Setup
- 2.1 Introduction
- 2.2 MSEL Settings
- 2.3 USB , Ethernet Port and Power Cables
- 2.4 Power up the DE10-Advanced Board with LXDE VNC Desktop Environment
Chapter 3 Software Installation
- 3.1 Introduction
- 3.2 Installing Quartus Prime software
- 3.3 Installing Intel SoC Embedded Design Suite
